Deshab-OS/CODE/linux

Linux 6.6 LTS for UTSM Dual-Kernel Architecture

Overview

This directory contains the Linux 6.6 LTS configuration and build scripts for the UTSM + Linux dual-kernel architecture. Linux runs as a VMX non-root guest under the UTSM hypervisor (VMX root).

Prerequisites

• WSL (Windows Subsystem for Linux) with Ubuntu 22.04+ installed

  wsl --install -d Ubuntu-22.04
  

• Build dependencies (inside WSL):

  sudo apt update
  sudo apt install -y build-essential bc flex bison libelf-dev libssl-dev cpio gzip git
  

• ~3GB free disk space

Building Linux

1. From WSL

# Navigate to the project (adjust path for your WSL mount)
cd /mnt/d/Code/Deshab/CODE/linux

# Make the build script executable
chmod +x build.sh

# Run the build (clones Linux 6.6 LTS, configures, builds)
./build.sh

The build will:

1. Clone Linux 6.6 LTS source to CODE/linux/src/
2. Apply UTSM patches from CODE/linux/patches/ (if any)
3. Configure with configs/utsm_x86_64_defconfig
4. Build bzImage
5. Copy to SYSTEM/boot/linux-bzImage
6. Build initramfs if CODE/linux/initramfs/ exists

2. Enable in Limine

After building, uncomment the Linux module entries in SYSTEM/limine/limine.conf:

    module_path: boot():/boot/linux-bzImage
    module_cmdline: linux:bzImage
    module_path: boot():/boot/linux-initrd.img
    module_cmdline: linux:initrd

3. Rebuild the disk image

cd d:\Code\Deshab
.\build.bat

4. Test with QEMU

Note: VMX requires hardware virtualization support. QEMU's TCG (software emulation) does NOT support VMX instructions. To test the VMX path:

• Real hardware: Boot on an Intel machine with VT-x enabled in BIOS
• QEMU with WHPX: qemu-system-x86_64 -accel whpx -cpu max (may not expose nested VMX to the guest)
• QEMU with KVM (Linux host only): qemu-system-x86_64 -enable-kvm -cpu host

Without VMX, UTSM gracefully falls back to the normal DSK boot flow.

Configuration Details

The utsm_x86_64_defconfig enables:

• 64-bit kernel with SMP support
• Serial console (8250/16550 at 0x3F8, 115200 baud)
• virtio: console, block, net, fs (for UTSM host backends)
• ext4, FAT, tmpfs, proc, sysfs filesystems
• No module loading (all drivers built-in for Phase 1)
• No EFI stub (UTSM uses custom VMX boot protocol)
• Debug info and printk timestamps

File Structure

CODE/linux/
├── configs/
│   └── utsm_x86_64_defconfig   # Kernel configuration
├── patches/                     # UTSM-specific kernel patches
│   ├── utsm-hcall.patch         # /dev/utsm hypercall driver (Phase 1.3)
│   ├── utsm-ipc.patch           # Shared memory IPC driver (Phase 1.3)
│   └── utsm-virtio.patch        # virtio enhancements (Phase 1.4+)
├── initramfs/                   # Minimal initramfs contents (optional)
├── build.sh                     # Build script (run in WSL/Linux)
└── README.md                    # This file

Boot Flow

Limine (UEFI)
  → utsm.elf (VMX root)
    → vmm_init() + vmm_self_test()
    → linux_loader_init() (parse bzImage, set up boot_params, EPT)
    → linux_launch() (VMCS config + vmlaunch)
      → Linux 6.6 startup_64 (VMX non-root)
        → Serial console output
        → virtio-console ↔ UTSM
        → virtio-fs mount /utsm
        → User space (init/shell)

Guest Networking (virtio-net)

UTSM vmm 侧模拟一块 virtio-net 网卡（virtio-mmio 模型，GPA 0xF4001000， guest ISA IRQ6），数据路径桥接到 host 真实网卡（e1000/virtio-net DKM 驱动， 经 kernel_api.net 的 tx/rx_poll 收发帧）。guest 内核 cmdline 已自动注入：

virtio_mmio.device=4K@0xF4001000:6

utsm_x86_64_defconfig 已启用 CONFIG_VIRTIO_NET=y（内置，非模块）， 内核启动后应出现 eth0（virtio-mmio 无 PCI 拓扑，网卡名固定为 eth0）：

# 确认网卡已识别（dmesg 应能看到 virtio_net  probe 日志）
ip link show

# 拉起接口
ip link set eth0 up

# 方式一：DHCP（QEMU user-net/slirp 环境，网关 10.0.2.2，DNS 10.0.2.3）
dhcpcd eth0
# 或：dhclient eth0

# 方式二：静态地址（无 DHCP 服务器时）
ip addr add 10.0.2.15/24 dev eth0
ip route add default via 10.0.2.2
echo "nameserver 10.0.2.3" > /etc/resolv.conf

# 验证连通性
ping -c3 10.0.2.2        # QEMU slirp 网关（永远在线，适合冒烟测试）
ping -c3 10.0.2.3        # slirp 内建 DNS
pacman -Sy               # 联网同步包数据库

注意事项：

• MAC 共用：guest virtio-net 的 MAC 与 host e1000 相同（UTSM 桥接模型， config 空间直接回填 host 网卡 MAC）。QEMU user-net 下 slirp 按 MAC 分配 10.0.2.15；若 host Deshab 原生网络栈同时用该网卡联网，两者会抢同一 DHCP 租约，实测时请只让一侧做 DHCP（或 host 完全不用网络）。
• MTU：后端按标准 1500 MTU 转发，不支持 GSO/TSO（feature 未协商， guest 自动走软件分片/checksum 路径）。
• 无中断收包：RX 走 UTSM 周期轮询（VMX preemption timer，~1kHz） 填充 guest RX ring 并注入 IRQ6；大流量下串口统计日志每 512 帧打印一行 [VNET] stat ...（rx_filled / rx_drop_nobuf / tx_sent / tx_drop）， 可用于判断包在哪一段丢失。
• 若 ip link 看不到 eth0：检查 dmesg 中 virtio_mmio probe 是否成功， 以及 host 串口日志是否有 [VNET] bound to UTSM net device 0 （host 侧 e1000/virtio-net DKM 驱动需先注册 netdev）。